South African Class 18 2-10-2

South African Class 18 2-10-2

300px Builder's picture of the Class 18, c. 1927

Type and origin Power type Steam Designer South African Railways (Col F.R. Collins DSO) Builder Henschel and Son Serial number 20787-20788 Model Class 18 Build date 1927 Total produced 2

Specifications Configuration 2-10-2 (Santa Fe) Driver axle 3rd coupled axle Gauge 3 ft 6 in (1,067 mm) Cape gauge Leading dia 30 in (762 mm) Coupled dia 57 in (1,448 mm) Trailing dia 33 in (838 mm) Tender wheels 34 in (864 mm) Minimum curve 320 ft (98 m) Wheelbase  • Engine  • Coupled 21 ft (6,401 mm)  • Tender 20 ft 5 in (6,223 mm)  • Tender bogie 6 ft 2 in (1,880 mm) Length:  • Over couplers 76 ft (23,165 mm) Height 13 ft (3,962 mm) Axle load  • Leading  • 1st coupled  • 2nd coupled  • 3rd coupled  • 4th coupled  • 5th coupled  • Trailing  • Tender bogie Bogie 1: Bogie 2:  • Tender axle Adhesive weight Loco weight Tender weight Loco & tender weight Tender type HT (2-axle bogies) Mechanical stoker Fuel type Coal Water cap Boiler:  • Pitch 8 ft 6 in (2,591 mm)  • Diameter  • Tube plates 20 ft 7 in (6,274 mm)  • Small tubes 160:  • large tubes 34:  • Firebox type Round-top Boiler pressure Safety valve Pop Firegrate area 60 sq ft (5.6 m2) Heating surface 3,231 sq ft (300.2 m2)  • Tubes 2,945 sq ft (273.6 m2)  • Firebox 265 sq ft (24.6 m2) Superheater:  • Heating area 850 sq ft (79 m2) Cylinders Three Cylinder size bore 28 in (711 mm) stroke Valve gear Outer Walschaerts - Inner Gresley Valve type Piston Couplers AAR knuckle

Performance figures Tractive effort 53,650 lbf (239 kN) @ 75%

Career Operators South African Railways Class Class 18 Number in class 2 Numbers 1360-1361 Nicknames Henschel Giant Delivered 1927-1928 First run 1927 Withdrawn 1951

The 3rd & 4th coupled axles had flangeless wheels

The South African Railways Class 18 2-10-2 of 1927 was a steam locomotive.

In December 1927 and January 1928, the South African Railways placed two Class 18 three-cylinder steam locomotives with a 2-10-2 Santa Fe type wheel arrangement in service on the Witbank-Germiston coal line.

Manufacturer

The Class 18 2-10-2 Santa Fe type steam locomotive was designed by Colonel F.R. Collins DSO, Chief Mechanical Engineer (CME) of the South African Railways (SAR) from 1922 to 1929, and built by Henschel and Son in Germany. Two locomotives were delivered in 1927 and 1928, numbered 1360 and 1361.

Characteristics

They were very powerful three-cylinder locomotives. At the time, three-cylindered locomotives were being built in appreciable numbers in Europe and America. Factors in their favour were their more even turning moment, improved balancing and better distribution of crank-pin thrust. Drawbacks were increased complexity and higher repair cost.

File:Col F.R. Collins DSO.jpg

Col F.R. Collins DSO

When delivered, the third cylinder was clearly visible, but plating was subsequently added beneath the smokebox and hid it from view. These were the most powerful non-articulated steam locomotives to see service on the SAR, with a tractive effort of 53,650 pounds-force (239 kilonewtons) at 75% boiler pressure and capable of hauling loads of 1,800 long tons (1,829 tonnes) over the ruling gradient of 1 in 100 (1%) on the Witbank-Apex section.

Contemporary Henschel publicity appropriately referred to them as the "Henschel Giants". They were larger in most respects than Deutsche Reichsbahn's new Standard gauge Class 44 three cylinder 2-10-0 locomotives. Although their all-up locomotive weight was almost the same, when considering the fact that the SAR's Cape gauge Class 18 had shorter axles and frame stretchers, saving weight that could then be built into other items such as the firebox, the Class 18 was the larger locomotive.

The Class 18 had a round-topped firebox with a combustion chamber, with arch tubes supporting the brick arch. It was fired by a Duplex D.4 type mechanical stoker, operated by a four-cylinder steam engine.

To allow the locomotive to negotiate curves of 320 feet (98 metres) radius despite its long coupled wheelbase, the third and fourth pairs of driving wheels were flangeless. In addition, the locomotive made use of a Krauss-Helmholtz bogie system, where the leading pair of driving wheels has a limited amount of sideplay with an articulated link to the leading bissel bogie. The bissel bogie was connected to a sleeve around the first driving axle so that any displacement of the bissel bogie in one direction would cause a similar displacement of the leading driving axle in the opposite direction, thereby steering the driving wheels through curves.

The outside cylinders drove the third pair of driving wheels, while the inside cylinder drove the second pair through a cranked axle, with the cylinder mounted in an inclined position. The three cranks were arranged at an angle of 120 degrees to each other, allowing for the inclination of the inner cylinder.

Service

The Class 18 was introduced in an attempt to ease problems which were being experienced with increasingly heavy coal trains on the line between Witbank and Germiston, where the Class MF Mallets were considered as being too sluggish and the hauling capacity of the non-articulated fleet was being stretched to the limit.

In spite of the two sets of flangeless coupled wheels and the Krauss-Helmholtz system, the Class 18 experienced excessive flange and tyre wear. In addition, the complicated valve gear was not robust enough and required high maintenance, frequently giving trouble owing to wear and breakage. The result was that the locomotives had to be shopped at under 40,000 miles (64,374 kilometres). Both Class 18 locomotives were withdrawn by 1951.

Knuckle couplers

Transition era knuckle coupler

In 1927, the SAR began to convert the couplers of its Cape Gauge rolling stock from the bell-shaped link-and-pin coupling system, which had been in use since the establishment of the Cape Government Railways in 1873, to AAR knuckle couplers. Judging from the official SAR Locomotive Diagram Book, the dimensional drawings as published by Holland, which were for the most part based on the original as-delivered and unmodified loco­motives, as well as contemporary photographs, the Class 18 were acquired new with knuckle couplers fitted, as were the Classes GCA, GF, HF and U, which also entered service in 1927.

Conversion of all rolling stock was to take several years and both coupler types could still be seen on rolling stock into the late 1950s. During the transition period, knuckle couplers on locomotives had a horizontal gap and a vertical hole in the knuckle itself to accommodate, respectively, a link and a pin, to enable it to couple to vehicles which were still equipped with the older link-and-pin couplers.

Illustration

• Class 18 2-10-2.jpg

  Class 18 with the third cylinder visible, as delivered, c. 1930

• Lok.HENSCEL(2040909).jpg

  Cutaway diagram of a Class 18 2-10-2 locomotive

• SAR Class 18 (2-10-2).jpg

  Class 18 at Germiston Loco with plating beneath the smokebox hiding the third cylinder